发电机组是一种起动迅速、操作维修方便、投资少、对环境的适应性能较强的发电装置。那么发电机组的机油中是怎么混入水的呢？下面红领巾瓜报组厂家为您分析分析：

The generator set is a kind of power generation device with fast starting, convenient operation and maintenance, low investment and strong adaptability to the environment. So how does the oil of the generator set mix with water? The following biogas generator unit manufacturers will analyze for you:

①水堵压装不紧导致松脱漏水；水堵烂透。

① The water plug is not tightly pressed, resulting in looseness and water leakage; The water is blocked and rotten.

解决的办法是更换水。

The solution is to replace the water.

水堵在缸体内面，看不到，其外面是(在排气管侧的工艺堵。若水堵孔腐蚀严重或碰损，应用铣刀扩孔少许，再选大一号水堵或自己车削一个水堵换上。

The water plug is on the inner surface of the cylinder block and cannot be seen. The outer part is the process plug (on the exhaust pipe side). If the water plug hole is seriously corroded or damaged, use a milling cutter to expand the hole a little, and then select a larger water plug or turn a water plug by yourself to replace it.

②气缸垫损坏或缸盖裂纹，水进入气门推杆孔而顺流到油底壳内。

② The cylinder head gasket is damaged or the cylinder head is cracked, and the water enters the valve pushrod hole and flows into the oil pan.

气缸垫冲烧，往往伴有哧哧的响声；有时，水漏入气缸中，此时燃烧排气的烟色为白雾状。仔细判断是哪一个缸损坏了，可用停缸法判断。查找判准后，更换气缸垫，若是缸头裂纹或砂眼，则可视情修理或更换。

When the cylinder gasket is burned, it is often accompanied by a wheezing noise; Sometimes, water leaks into the cylinder, and the smoke color of combustion exhaust is white fog. Carefully judge which cylinder is damaged, and use the cylinder shutdown method to judge. After finding and determining, replace the cylinder gasket. If the cylinder head cracks or sand holes, repair or replace them as appropriate.

③机体上有砂眼。

③ There are sand holes on the body.

特别是在缸体上的水室部位，该部位有主油道，与主轴瓦孔有斜油道相通，如有砂眼、缩松等铸造缺陷，将有水漏入油底壳内。可卸下油底壳查看，若发现主轴瓦孔处出水，则说明油道与水室相通。若检查冷却液，则其内一定混入机油漂浮其上。若无机油漂浮，则说明砂眼在其它部位，认真观察缸体内什么部位漏水。为确保发动机的使用，更换缸体总成，防止出现化瓦事故。

Especially in the water chamber on the cylinder block, there is a main oil passage, which is connected with the inclined oil passage of the main bearing hole. If there are casting defects such as sand holes and shrinkage porosity, water will leak into the oil pan. The oil pan can be removed for inspection. If water is found at the main bearing hole, it means that the oil passage is connected with the water chamber. If the coolant is checked, it must be mixed with oil and float on it. If there is no oil floating, it means that the sand hole is in other parts. Carefully observe which part of the cylinder leaks. In order to ensure the use of the engine, replace the cylinder block assembly to prevent the occurrence of the accident.

发电机组的机油中是怎么混入水？这个问题，我们从叁个方面来为您讲解完毕了，您是否了解了呢？更多事项就来我们网站咨询吧！

How is water mixed in the engine oil of the generator set? We have explained this question to you from three aspects. Do you understand it? Come to our website for more matters Ask!