瓦斯发电机组在正常使用过程中，可能会由于各种原因导致进水，那么发电机组进水后还能不能继续使用?下面和小编一起来了解一下。

During the normal use of the gas generator set, water may enter the water due to various reasons. Can the generator set continue to be used after water enters the water? Let's have a look with Xiao Bian.

我们要了解为什么会进水：

We need to understand why water enters:

1、由于燃油箱没有清洗干净，只要清洗干净了就基本不会出现进水现象。

1. Because the fuel tank is not cleaned, as long as it is cleaned, there will be no water ingress.

2、油品有问题，小编建议用户到正规加油站购买的，从私人或无资质的公司购买的便宜燃油极可能混有过多杂质或水分。

2. There is a problem with the oil. Xiaobian suggests that the cheap fuel purchased from private or unqualified enterprises from regular gas stations may be mixed with too much impurities or moisture.

3、燃油箱只有两个口，一个机和燃油箱连接的是高压油泵，一般不可能是发动机出问题这边的水回流。

3. There are only two ports in the fuel tank. One engine is connected to the fuel tank by a high-pressure oil pump. Generally, it is not possible that the engine has a problem.

另一个入口就是燃油箱加油口，如果燃油箱处于室外，是很有可能雨水渗入燃油箱内部。

The other entrance is the fuel tank filler. If the fuel tank is outside, it is likely that rain will seep into the fuel tank.

小编提醒各位进水后是不能继续使用的，因为水是无法被压缩的，油水混合进入到汽缸后，发动机依然还牌调整运转期间，做功的过程中不能对水进行压缩，从而导致活塞卡死，汽缸磨损情况会变得加剧。

The editor reminds you that water can't be used after water ingress, because water can't be compressed. After oil and water are mixed into the cylinder, the engine is still under adjustment and operation, and water can't be compressed during work, resulting in piston seizure and cylinder wear.

如果中有水，除了会导致发电机组运转缓慢且不稳定之外，甚至还可能造成曲轴弯曲等，对发电机组的正常运行带来非常严重的影响。

If there is water in it, in addition to causing slow and unstable operation of the generator set, it may even cause bending of the crankshaft, which will have a very serious impact on the normal operation of the generator set.

一般发生发电机组进水后，要尽快把电瓶负极线拆下来，以免发电机的控制系统因时水而发生短路，同时按正确步骤更换燃油滤清器。

Generally, after water enters the generator set, remove the negative wire of the battery as soon as possible to avoid short circuit of the control system of the generator due to water. At the same time, replace the fuel filter according to the correct steps.

如果进水不是很多，可以先让静置一段时间，让水慢慢沉淀下去，等到水和成分层后，再将水排净即可。而如果是进水的量比较大，则应将原有的变质全部更换，否则可能会造成机组运行冒白烟或运行无力。更多相关事项就来我们网站咨询！

If there is not much water inflow, you can let it stand for a period of time, let the water settle down slowly, and then drain the water after the water and the composition layer. However, if the amount of water inflow is large, the original deterioration should be replaced completely, otherwise it may cause white smoke or weak operation of the unit. Come to our website for more relevant matters consulting service