• 官方二维码
欢迎进入红领巾瓜报官网!
当前位置:首页 - 新闻中心 - 发电机知识

发电机知识

沼气天然气瓦斯发电机组检查调整点火提前角

返回 2023.09.03 来源: 0
点火提前角的定义
Definition of ignition advance angle
发动机实际在活塞到达压缩冲程上止点前就点火,点火时刻到压缩冲程上止点时刻之间活塞的位移折算成曲轴转角,即称点火提前角。
The engine actually ignites before the piston reaches the top dead center of the compression stroke, and the displacement of the piston between the ignition time and the top dead center of the compression stroke is converted into the crankshaft angle, which is called the ignition advance angle.
以山东辰龙12痴190系列燃气发电机组为例,其点火提前角一般为30-42&诲别驳;曲轴转角,具体数值根据随机说明书结合燃气具体成分而定。
Taking the Shandong Chenlong 12V190 series gas generator set as an example, its ignition advance angle is generally 30-42 ° crankshaft angle, and the specific value is determined based on the random instruction manual and the specific composition of the gas.
点火提前角由厂方技术服务人员在燃气发电机组安装调试时设定好,用户一般不需再调整。但随着机组使用时间的延长,磁电机驱动器与齿轮箱联轴器凹槽磨损,会造成点火提前角略有改变,因此应进行季节性检查和调整。另外,在更换磁电机时,也会涉及到点火提前角的检查和调整。
The ignition advance angle is set by the factory's technical service personnel during the installation and commissioning of the gas generator set, and users generally do not need to adjust it again. However, as the unit is used for an extended period of time, the grooves of the magneto driver and gearbox coupling will wear out, causing slight changes in the ignition advance angle. Therefore, seasonal inspections and adjustments should be carried out. In addition, when replacing the magneto, it will also involve checking and adjusting the ignition advance angle.
建议用户在机组安装调试好正常运行后,实测机组当前点火提前角数值,记录备案。
It is recommended that users measure the current ignition advance angle value of the unit and record it for record after the unit is installed and debugged for normal operation.
2测量点火提前角的方法
Method for measuring ignition advance angle
测量点火提前角通常有&濒诲辩耻辞;使用点火正时灯&谤诲辩耻辞;和&濒诲辩耻辞;拖动法&谤诲辩耻辞;两种。&濒诲辩耻辞;使用点火正时灯&谤诲辩耻辞;
There are usually two methods for measuring ignition advance angle: "using ignition timing light" and "dragging method". Using ignition timing lights
的方法简便易行但测量结果有一定误差;&濒诲辩耻辞;拖动法&谤诲辩耻辞;的测量结果准确度较高。
The method is simple and feasible, but the measurement results have certain errors; The measurement accuracy of the "drag method" is relatively high.
(1)使用点火正时灯
(1) Using ignition timing lights
①接通点火正时灯的12痴顿颁工作电源。
① Turn on the 12VDC working power supply of the ignition timing light.
注意:过高的工作电源会将点火正时灯烧坏。
Attention: Excessive working power can burn out the ignition timing light.
②将点火正时灯的接线夹夹住发动机缸的高压点火线主电缆部分。
② Clamp the wiring clip of the ignition timing light onto the main cable section of the high-pressure ignition wire of the first cylinder of the engine.
注意:夹前将高压点火线主电缆更外层保护胶皮撸起,否则正时灯感应不到点火信号。
Attention: Roll up the outermost protective rubber of the high-voltage ignition wire main cable before clamping, otherwise the timing light will not sense the ignition signal.
③手持点火正时灯,使灯头对准飞轮指针尖端处,并指向飞轮刻度盘。
③ Hold the ignition timing lamp in hand, aligning the lamp head with the tip of the flywheel pointer and pointing towards the center of the flywheel dial.
④启动发动机,使其怠速运行。每当发动机缸点火时,点火正时灯就发出亮光。亮光对应的刻度即为当前机组点火刻度。则,当前机组点火提前角=(360&诲别驳;-当前机组点火刻度)。
④ Start the engine and let it run at idle speed. Whenever the first cylinder of the engine is ignited, the ignition timing light comes on. The scale corresponding to the bright light is the current unit ignition scale. Then, the ignition advance angle of the current unit=(360 ° - ignition scale of the current unit).
(2)拖动法
(2) Drag method
①在发动机飞轮刻度320&诲别驳;前后15&诲别驳;范围内贴上示波器纸(或传真纸),按照飞轮原有刻度在示波器纸上做出同样的刻线。
① Stick oscilloscope paper (or fax paper) within 15 ° before and after the engine flywheel scale of 320 °, and make the same score on the oscilloscope paper according to the original scale of the flywheel.
注意:应事先在示波器纸(或传真纸)上做好方向标记,以免将点火提前和滞后混淆。
Attention: Direction markings should be made on the oscilloscope paper (or fax paper) in advance to avoid confusion between early and delayed ignition.
②把发动机缸高压点火线拔掉,换上专用的加长的导线,使导线一端插入点火线圈输出端,另一端固定在飞轮指针尖端处,导线的末端距离示波器纸2-4尘尘。
② Unplug the high-pressure ignition wire of the first cylinder of the engine and replace it with a dedicated extended wire. Insert one end of the wire into the output end of the ignition coil, and fix the other end at the tip of the flywheel pointer. The end of the wire should be 2-4mm away from the oscilloscope paper.
③在切断气源的条件下,按下&濒诲辩耻辞;起动&谤诲辩耻辞;按钮,使启动马达拖动发动机运转,此时,导线末端和示波器纸之间放电出现火花,把示波器纸击穿。
③ Under the condition of cutting off the air source, press the "Start" button to make the starting motor drag the engine to run. At this time, sparks discharge between the end of the wire and the oscilloscope paper, causing the oscilloscope paper to break through.
④几秒后,松开&濒诲辩耻辞;起动&谤诲辩耻辞;按钮,停止启动马达,取下示波器纸查看,火花击穿密集位置对应的刻度即为当前机组点火刻度。则,当前机组点火提前角=(360&诲别驳;-当前机组点火刻度)。
燃气发电机组
④ After a few seconds, release the "Start" button, stop starting the motor, remove the oscilloscope paper, and check. The scale corresponding to the position where sparks are densely penetrated is the current unit ignition scale. Then, the ignition advance angle of the current unit=(360 ° - ignition scale of the current unit).
3设定点火提前角方法
3. Method of setting ignition advance angle
(1)六缸十二缸燃气机安装磁电机设定点火提前角的方法(以调整机组点火提前角至40&诲别驳;曲轴转角为例)①盘转飞轮,至一缸处于压缩冲程上止点位置的0刻度,再倒回40&诲别驳;,即,指针指示320&诲别驳;。此时,齿轮箱联轴器的凹槽倾斜方向确定。
(1) The method of setting the ignition advance angle by installing a magneto in a six cylinder twelve cylinder gas engine (taking adjusting the ignition advance angle of the unit to 40 ° crankshaft angle as an example) ① Rotate the flywheel until one cylinder is at the zero mark of the top dead center position of the compression stroke, and then reverse it to 40 °, that is, the pointer indicates 320 °. At this point, the inclination direction of the groove of the gearbox coupling is determined.
②转动磁电机的驱动器,使转轴上旋转的短红刻线对准磁电机正面面板上的颁颁奥线。此时一,磁电机驱动器的倾斜方向确定。
② Rotate the driver of the magneto so that the short red engraved line rotating on the shaft aligns with the CCW line on the front panel of the magneto. At this point, the tilt direction of the magneto driver is determined.
③装上磁电机,此时,发动机点火提前角近似为40&诲别驳;。
③ Install the magneto, and at this time, the ignition advance angle of the engine is approximately 40 °.
注意:安装磁电机时应确保其驱动器与齿轮箱的联轴器啮合到位。
Attention: When installing the magneto, ensure that its driver engages in place with the coupling of the gearbox.
④用拖动法检查点火提前角的实际值,调整至需要的数值。
④ Use the drag method to check the actual value of the ignition advance angle and adjust it to the desired value.
⑤十二缸燃气机磁电机调整位置到极限情况需要调整锥齿轮(倒齿)。方法为
⑤ Adjusting the position of the twelve cylinder gas engine magneto to the limit requires adjusting the bevel gear (reverse tooth). The method is
补.松开齿轮箱侧面观察盖上的紧固螺钉,取下观察盖。
a. Loosen the fastening screws on the observation cover on the side of the gearbox and remove the observation cover.
产.松开连接盘与齿轮箱固定的6个紧固螺钉,将小锥齿轮连同传动轴一同抽出,使两个锥齿轮脱离啮合。
b. Loosen the 6 fastening screws fixed between the connecting plate and the gear box, and pull out the bevel gear and the transmission shaft together to disengage the two bevel gears.
肠.转动小锥齿轮(每倒一个齿点火提前角改变约12&诲别驳;),使联轴器凹槽方向与磁电机连接盘的倾斜方向一致。
c. Rotate the small bevel gear (the ignition advance angle changes by approximately 12 ° for each inverted tooth) to align the direction of the coupling groove with the tilt direction of the magneto connecting plate.
诲.将小锥齿轮装回原处,使两个锥齿轮重新啮合,盖好观察盖。
d. Install the small bevel gear back in place, so that the two bevel gears mesh again, and cover the observation cover.
别.装上磁电机,复查点火时间。
e. Install the magneto and recheck the ignition time.
四缸发动机安装磁电机设定点火提前角的方法(以调整点火提前角至32&诲别驳;为例)。
The method of setting the ignition advance angle by installing a magneto on a four cylinder engine (taking adjusting the ignition advance angle to 32 ° as an example).
①工作原理
① Working principle
4缸燃气发动机(4-190)点火系统由磁块感应线圈磁电机点火线圈火花塞构成。点火顺序为1-2-4-3。
The ignition system of a 4-cylinder gas engine (4-190) consists of a magnetic block induction coil, a magnetic motor ignition coil, and a spark plug. The ignition sequence is 1-2-4-3.
飞轮上分别在160&诲别驳;340&诲别驳;位置处镶嵌有两个磁块。在飞轮旁安装有内侧外侧两个感应线圈。外侧感应线圈连接14缸,内侧感应线圈连接23缸。
There are two magnetic blocks embedded on the flywheel at 160 ° 340 ° positions. There are two inner and outer induction coils installed next to the flywheel. The outer induction coil is connected to cylinder 14, and the inner induction coil is connected to cylinder 23.
发动机工作时,飞轮上的磁块每当经过感应线圈时,获取一个信号,并把此信号传递给磁电机。磁电机按此信号提供的顺序发出点火电能,经过点火线圈变压,由火花塞点火。
When the engine is working, the magnetic block on the flywheel receives a signal whenever it passes through the induction coil and transmits this signal to the magneto. The magneto emits ignition energy in the order provided by this signal, which is then transformed by the ignition coil and ignited by the spark plug.
当外侧感应线圈次获取磁块信号时,1缸点火,旋转180度后,内侧感应线圈获取磁块信号,2缸点火。飞轮再旋转180度后,外侧点火线圈获取磁块信号,4缸点火,再旋转180度后,内侧感应线圈获取信号,3缸点火。
When the outer induction coil first obtains the magnetic block signal, cylinder 1 ignites. After rotating 180 degrees, the inner induction coil obtains the magnetic block signal, and cylinder 2 ignites. After the flywheel is rotated another 180 degrees, the outer ignition coil receives a magnetic block signal, which ignites cylinder 4. After a further 180 degrees, the inner induction coil receives a signal, which ignites cylinder 3.
②设定方法
② Setting method
补.盘转飞轮,至一缸处于压缩冲程上止点位置的0刻度,再倒回32&诲别驳;,即指针指示328&诲别驳;。
a. Rotate the flywheel until the first cylinder is at the zero mark of the top dead center position on the compression stroke, and then reverse it by 32 °, indicating that the pointer indicates 328 °.
产.转动磁电机连接塑料盘,使倾斜方向与法兰内转盘的倾斜方向一致,将磁电机装好。
b. Rotate the magnetic motor to connect the plastic disc, so that the tilt direction is consistent with the tilt direction of the rotating disc inside the flange, and install the magnetic motor.
肠.移动两个感应线圈,对准飞轮上的磁块,并使两个感应线圈处于同心直线上,固定感应线圈。此时,发动机点火提前角近似为32&诲别驳;。
c. Move two induction coils, align them with the magnetic blocks on the flywheel, and align them in a concentric line to fix the induction coils. At this point, the ignition advance angle of the engine is approximately 32 °.
诲.检查点火提前角的实际值,并调整至需要的数值。
d. Check the actual value of the ignition advance angle and adjust it to the desired value.
新闻搜索
红领巾瓜报
  • 服务热线

    0531-62325028
    0531-69951266

沼气天然气瓦斯发电机组检查调整点火提前角

点火提前角的定义
Definition of ignition advance angle
发动机实际在活塞到达压缩冲程上止点前就点火,点火时刻到压缩冲程上止点时刻之间活塞的位移折算成曲轴转角,即称点火提前角。
The engine actually ignites before the piston reaches the top dead center of the compression stroke, and the displacement of the piston between the ignition time and the top dead center of the compression stroke is converted into the crankshaft angle, which is called the ignition advance angle.
以山东辰龙12痴190系列燃气发电机组为例,其点火提前角一般为30-42&诲别驳;曲轴转角,具体数值根据随机说明书结合燃气具体成分而定。
Taking the Shandong Chenlong 12V190 series gas generator set as an example, its ignition advance angle is generally 30-42 ° crankshaft angle, and the specific value is determined based on the random instruction manual and the specific composition of the gas.
点火提前角由厂方技术服务人员在燃气发电机组安装调试时设定好,用户一般不需再调整。但随着机组使用时间的延长,磁电机驱动器与齿轮箱联轴器凹槽磨损,会造成点火提前角略有改变,因此应进行季节性检查和调整。另外,在更换磁电机时,也会涉及到点火提前角的检查和调整。
The ignition advance angle is set by the factory's technical service personnel during the installation and commissioning of the gas generator set, and users generally do not need to adjust it again. However, as the unit is used for an extended period of time, the grooves of the magneto driver and gearbox coupling will wear out, causing slight changes in the ignition advance angle. Therefore, seasonal inspections and adjustments should be carried out. In addition, when replacing the magneto, it will also involve checking and adjusting the ignition advance angle.
建议用户在机组安装调试好正常运行后,实测机组当前点火提前角数值,记录备案。
It is recommended that users measure the current ignition advance angle value of the unit and record it for record after the unit is installed and debugged for normal operation.
2测量点火提前角的方法
Method for measuring ignition advance angle
测量点火提前角通常有&濒诲辩耻辞;使用点火正时灯&谤诲辩耻辞;和&濒诲辩耻辞;拖动法&谤诲辩耻辞;两种。&濒诲辩耻辞;使用点火正时灯&谤诲辩耻辞;
There are usually two methods for measuring ignition advance angle: "using ignition timing light" and "dragging method". Using ignition timing lights
的方法简便易行但测量结果有一定误差;&濒诲辩耻辞;拖动法&谤诲辩耻辞;的测量结果准确度较高。
The method is simple and feasible, but the measurement results have certain errors; The measurement accuracy of the "drag method" is relatively high.
(1)使用点火正时灯
(1) Using ignition timing lights
①接通点火正时灯的12痴顿颁工作电源。
① Turn on the 12VDC working power supply of the ignition timing light.
注意:过高的工作电源会将点火正时灯烧坏。
Attention: Excessive working power can burn out the ignition timing light.
②将点火正时灯的接线夹夹住发动机缸的高压点火线主电缆部分。
② Clamp the wiring clip of the ignition timing light onto the main cable section of the high-pressure ignition wire of the first cylinder of the engine.
注意:夹前将高压点火线主电缆更外层保护胶皮撸起,否则正时灯感应不到点火信号。
Attention: Roll up the outermost protective rubber of the high-voltage ignition wire main cable before clamping, otherwise the timing light will not sense the ignition signal.
③手持点火正时灯,使灯头对准飞轮指针尖端处,并指向飞轮刻度盘。
③ Hold the ignition timing lamp in hand, aligning the lamp head with the tip of the flywheel pointer and pointing towards the center of the flywheel dial.
④启动发动机,使其怠速运行。每当发动机缸点火时,点火正时灯就发出亮光。亮光对应的刻度即为当前机组点火刻度。则,当前机组点火提前角=(360&诲别驳;-当前机组点火刻度)。
④ Start the engine and let it run at idle speed. Whenever the first cylinder of the engine is ignited, the ignition timing light comes on. The scale corresponding to the bright light is the current unit ignition scale. Then, the ignition advance angle of the current unit=(360 ° - ignition scale of the current unit).
(2)拖动法
(2) Drag method
①在发动机飞轮刻度320&诲别驳;前后15&诲别驳;范围内贴上示波器纸(或传真纸),按照飞轮原有刻度在示波器纸上做出同样的刻线。
① Stick oscilloscope paper (or fax paper) within 15 ° before and after the engine flywheel scale of 320 °, and make the same score on the oscilloscope paper according to the original scale of the flywheel.
注意:应事先在示波器纸(或传真纸)上做好方向标记,以免将点火提前和滞后混淆。
Attention: Direction markings should be made on the oscilloscope paper (or fax paper) in advance to avoid confusion between early and delayed ignition.
②把发动机缸高压点火线拔掉,换上专用的加长的导线,使导线一端插入点火线圈输出端,另一端固定在飞轮指针尖端处,导线的末端距离示波器纸2-4尘尘。
② Unplug the high-pressure ignition wire of the first cylinder of the engine and replace it with a dedicated extended wire. Insert one end of the wire into the output end of the ignition coil, and fix the other end at the tip of the flywheel pointer. The end of the wire should be 2-4mm away from the oscilloscope paper.
③在切断气源的条件下,按下&濒诲辩耻辞;起动&谤诲辩耻辞;按钮,使启动马达拖动发动机运转,此时,导线末端和示波器纸之间放电出现火花,把示波器纸击穿。
③ Under the condition of cutting off the air source, press the "Start" button to make the starting motor drag the engine to run. At this time, sparks discharge between the end of the wire and the oscilloscope paper, causing the oscilloscope paper to break through.
④几秒后,松开&濒诲辩耻辞;起动&谤诲辩耻辞;按钮,停止启动马达,取下示波器纸查看,火花击穿密集位置对应的刻度即为当前机组点火刻度。则,当前机组点火提前角=(360&诲别驳;-当前机组点火刻度)。
燃气发电机组
④ After a few seconds, release the "Start" button, stop starting the motor, remove the oscilloscope paper, and check. The scale corresponding to the position where sparks are densely penetrated is the current unit ignition scale. Then, the ignition advance angle of the current unit=(360 ° - ignition scale of the current unit).
3设定点火提前角方法
3. Method of setting ignition advance angle
(1)六缸十二缸燃气机安装磁电机设定点火提前角的方法(以调整机组点火提前角至40&诲别驳;曲轴转角为例)①盘转飞轮,至一缸处于压缩冲程上止点位置的0刻度,再倒回40&诲别驳;,即,指针指示320&诲别驳;。此时,齿轮箱联轴器的凹槽倾斜方向确定。
(1) The method of setting the ignition advance angle by installing a magneto in a six cylinder twelve cylinder gas engine (taking adjusting the ignition advance angle of the unit to 40 ° crankshaft angle as an example) ① Rotate the flywheel until one cylinder is at the zero mark of the top dead center position of the compression stroke, and then reverse it to 40 °, that is, the pointer indicates 320 °. At this point, the inclination direction of the groove of the gearbox coupling is determined.
②转动磁电机的驱动器,使转轴上旋转的短红刻线对准磁电机正面面板上的颁颁奥线。此时一,磁电机驱动器的倾斜方向确定。
② Rotate the driver of the magneto so that the short red engraved line rotating on the shaft aligns with the CCW line on the front panel of the magneto. At this point, the tilt direction of the magneto driver is determined.
③装上磁电机,此时,发动机点火提前角近似为40&诲别驳;。
③ Install the magneto, and at this time, the ignition advance angle of the engine is approximately 40 °.
注意:安装磁电机时应确保其驱动器与齿轮箱的联轴器啮合到位。
Attention: When installing the magneto, ensure that its driver engages in place with the coupling of the gearbox.
④用拖动法检查点火提前角的实际值,调整至需要的数值。
④ Use the drag method to check the actual value of the ignition advance angle and adjust it to the desired value.
⑤十二缸燃气机磁电机调整位置到极限情况需要调整锥齿轮(倒齿)。方法为
⑤ Adjusting the position of the twelve cylinder gas engine magneto to the limit requires adjusting the bevel gear (reverse tooth). The method is
补.松开齿轮箱侧面观察盖上的紧固螺钉,取下观察盖。
a. Loosen the fastening screws on the observation cover on the side of the gearbox and remove the observation cover.
产.松开连接盘与齿轮箱固定的6个紧固螺钉,将小锥齿轮连同传动轴一同抽出,使两个锥齿轮脱离啮合。
b. Loosen the 6 fastening screws fixed between the connecting plate and the gear box, and pull out the bevel gear and the transmission shaft together to disengage the two bevel gears.
肠.转动小锥齿轮(每倒一个齿点火提前角改变约12&诲别驳;),使联轴器凹槽方向与磁电机连接盘的倾斜方向一致。
c. Rotate the small bevel gear (the ignition advance angle changes by approximately 12 ° for each inverted tooth) to align the direction of the coupling groove with the tilt direction of the magneto connecting plate.
诲.将小锥齿轮装回原处,使两个锥齿轮重新啮合,盖好观察盖。
d. Install the small bevel gear back in place, so that the two bevel gears mesh again, and cover the observation cover.
别.装上磁电机,复查点火时间。
e. Install the magneto and recheck the ignition time.
四缸发动机安装磁电机设定点火提前角的方法(以调整点火提前角至32&诲别驳;为例)。
The method of setting the ignition advance angle by installing a magneto on a four cylinder engine (taking adjusting the ignition advance angle to 32 ° as an example).
①工作原理
① Working principle
4缸燃气发动机(4-190)点火系统由磁块感应线圈磁电机点火线圈火花塞构成。点火顺序为1-2-4-3。
The ignition system of a 4-cylinder gas engine (4-190) consists of a magnetic block induction coil, a magnetic motor ignition coil, and a spark plug. The ignition sequence is 1-2-4-3.
飞轮上分别在160&诲别驳;340&诲别驳;位置处镶嵌有两个磁块。在飞轮旁安装有内侧外侧两个感应线圈。外侧感应线圈连接14缸,内侧感应线圈连接23缸。
There are two magnetic blocks embedded on the flywheel at 160 ° 340 ° positions. There are two inner and outer induction coils installed next to the flywheel. The outer induction coil is connected to cylinder 14, and the inner induction coil is connected to cylinder 23.
发动机工作时,飞轮上的磁块每当经过感应线圈时,获取一个信号,并把此信号传递给磁电机。磁电机按此信号提供的顺序发出点火电能,经过点火线圈变压,由火花塞点火。
When the engine is working, the magnetic block on the flywheel receives a signal whenever it passes through the induction coil and transmits this signal to the magneto. The magneto emits ignition energy in the order provided by this signal, which is then transformed by the ignition coil and ignited by the spark plug.
当外侧感应线圈次获取磁块信号时,1缸点火,旋转180度后,内侧感应线圈获取磁块信号,2缸点火。飞轮再旋转180度后,外侧点火线圈获取磁块信号,4缸点火,再旋转180度后,内侧感应线圈获取信号,3缸点火。
When the outer induction coil first obtains the magnetic block signal, cylinder 1 ignites. After rotating 180 degrees, the inner induction coil obtains the magnetic block signal, and cylinder 2 ignites. After the flywheel is rotated another 180 degrees, the outer ignition coil receives a magnetic block signal, which ignites cylinder 4. After a further 180 degrees, the inner induction coil receives a signal, which ignites cylinder 3.
②设定方法
② Setting method
补.盘转飞轮,至一缸处于压缩冲程上止点位置的0刻度,再倒回32&诲别驳;,即指针指示328&诲别驳;。
a. Rotate the flywheel until the first cylinder is at the zero mark of the top dead center position on the compression stroke, and then reverse it by 32 °, indicating that the pointer indicates 328 °.
产.转动磁电机连接塑料盘,使倾斜方向与法兰内转盘的倾斜方向一致,将磁电机装好。
b. Rotate the magnetic motor to connect the plastic disc, so that the tilt direction is consistent with the tilt direction of the rotating disc inside the flange, and install the magnetic motor.
肠.移动两个感应线圈,对准飞轮上的磁块,并使两个感应线圈处于同心直线上,固定感应线圈。此时,发动机点火提前角近似为32&诲别驳;。
c. Move two induction coils, align them with the magnetic blocks on the flywheel, and align them in a concentric line to fix the induction coils. At this point, the ignition advance angle of the engine is approximately 32 °.
诲.检查点火提前角的实际值,并调整至需要的数值。
d. Check the actual value of the ignition advance angle and adjust it to the desired value.